Pinnacle Systems, Inc. - Safety Light Curtains, Safety Mat Systems and Ergonomic Palm Buttons
Page: 1CPS Series

1CPS Series Cable Pull Switch

Description:

The 1CPS Cable Pull Safety Switch is intended for use in applications with the cable runs up to 76 m [250 ft], such as conveyor runs within defined system zones. It is a cost-effective means of providing this emergency stop signal compared to multiple emergency stop push buttons. (Cable Pull Safety Switches are not, however, to be used as a means of personnel safeguarding. They may be used to prevent further injury or damage to equipment when used for emergency stop signaling.)

The 1CPS Series Cable Pull Safety Switch is designed to provide emergency stop protection for exposed conveyor lines. The internal mechanism latches on both slackened cable (push) and pulled cable. This capability enhances productivity by eliminating nuisance stops due to variations in temperature, stretch of cable over time, and other application variables.

A line in the midpoint of the cable tension window indicates proper cable tension, providing easy and intuitive set-up. The direct acting switch contacts are held closed when the actuating cable is under proper tension and the reset knob is set to RUN. When the actuating cable is pulled, slackened or broken, a cam positively opens the NC (Normally Closed) switch contacts. The snap action, trip operation causes the switch contacts to change state and mechanically latch almost simultaneously when the cable is pulled, slackened or broken. The NC switch contacts remain open until the 1CPS is reset by properly tensioning the cable and manually rotating the reset knob.

When the direct acting switch contacts open, the auxiliary contacts also actuate (open contacts close and closed contacts open). The auxiliary contacts are electrically isolated from the direct acting switch contacts. These NO (Normally Open) contacts may be used for monitoring or signaling.

The 1CPS complies with: Low Voltage Directive 73/23/EEC, as amended by directive 93/68/EEC; Machinery Directive 98/37/EEC only as the directives relate to the components being used in a safety function; IEC/EN60947-1; IEC/EN60947-5-1; IEC/EN60947-5-5.

Features:

Potential Applications:

1CPS Series Models Available 

 

 Part Number 1CPSA2
 Description Single direction cable (rope pull) switch; Up to 250 foot span; Wide temperature tolerance; Designed to reduce nuisance stops
 Features Cable, Maintained,  ½“ NPT Conduit; Hardware packets available separately
 Housing Material Die Cast Zinc
 Approvals UL, CSA, CE, BG
 Sealing IP67, NEMA 1, 4, 12, 13
 Electrical 2.8A @ 24VDC; 6A @120VAC
 Circuitry 2NC/2NO
 Measurements 172.7mm x 88.9mm x 65.2mm
 Temperature Range -25C to 80C


 

Additional Downloads

 

 

1CPS Single Page Printable Document  

 

 


 

 

1CPS Engineering Drawings  

 

 



 

 

 
Print this page

Safety Light Curtains
   Safety Light Curtain Comparison
   Model SS Solid State Outputs Safety Light Curtain
   Model SS Product Overview
   Model SS Blanking Options
   Model SS Safety Relay
   Model SS Specs and Dimensions
   Model SS Ordering Procedure
   Model SS Accessories
   Model MG Metal Box Controller and Safety Light Curtain
   Model MG Product Overview
   Model MG Smart Controller
   Model MG Design Criteria
   Model MG Features
   Model MG Dimensions
   Model MG Blanking Options
   Model MG Ordering Procedure
   Model MG Accessories
   Model MG Ethernet Option
   Model DR DIN-rail Controller and Safety Light Curtain
   Model DR Product Overview
   Model DR Smart Controller
   Model DR Design Criteria
   Model DR Features
   Model DR Dimensions
   Model DR Blanking Options
   Model DR Ordering Procedure
   Model DR Accessories
   Model CE Solid State Outputs Global Safety Light Curtain
   Model CE Product Overview
   Model CE Blanking Options
   Model CE Safety Relay
   Model CE Specs and Dimensions
   Model CE Ordering Procedure
   Model CE Accessories
   Model CA Cascading Safety Light Curtain
   Model CA Product Overview
   Model CA Blanking Options
   Model CA Safety Relay
   Model CA Specs and Dimensions
   Model CA Ordering/Pricing Procedure
   Model CA Accessories
   Model PPG Perimeter Guarding
   Model PPG Product Overview
   Model PPG Dimensions
   Model PPG Ordering Procedure
   Model PPG Accessories
Safety Mat Systems
   NSD Safety Mat System
   NSD Product Overview
   NSD No Steel Electrodes?
   NSD Mat Controllers
   NSD Layout Procedure
   NSD Trim Kits
   NSD Ordering Procedure
   NSD Sizing Your System
   NSD Wiring Options
   NSD Safety Modules
   STTS Safety Mat System
   STTS Product Overview
   STTS Design Criteria
   STTS Mat Controllers
   STTS Controller Dimensions
   STTS Layout Procedure
   STTS Trim Kits
   STTS Ordering Procedure
   STTS Sizing Your System
   Direction of Travel Mats
   High-Temp Welding Mats
Ergonomic Palm Buttons
   UltraTouch Product Overview
   What can UltraTouch do for you?
   UltraTouch Benefits
   Ergonomic Palm Button Comparison
   UltraTouch Specifications
   UltraTouch Dimensions
   UltraTouch Models Available
   UltraTouch Ordering Procedure and Finding a Part Number
   UltraTouch Accessories
Programmable Safety Controller
Safety Interlock Switches
   GKM Series
   GKN Series
   GKE Series
   GK Series
   GKR/GKL Series
   GSS Series
   1CPS Series
   2CPS Series
   FF3-21-DC-03
   FF5-21-DC-03
   FF6-10-DC-03
   FFS-11-03
   BX Series
   GSX Series
   CLSX Series
   Stack Lights Product Overview
   Stack Lights Ordering Procedure
   Stack Lights Dimensions
   Stack Lights Specifications
   Stack Lights Wiring Diagrams
   Stack Lights Accessories
   Stack Lights Accessories Mounting Poles
   Stack Lights Accessories Mounting Bases
   Stack Lights Wall Accessories Mount Brackets
Fencing
   Fencing Overview
   Fencing Specifications
   Fencing Styles
   Complies with Safety Standards
   OSHA Table 0-10
   Fencing Warranty
   Proposal Request
E-Stops & Stack Lights
Metal Stamping / Pressroom Products
   Press Control Design Criteria
   Punch Press Clutch/Brake Controls
   Press Automation
   Die Protection
   Tonnage Monitoring
   Programmable Limit Switches
   Time-Based Brake Monitors
Safety Glossary
   Glossary A-C
   Glossary D-F
   Glossary G-I
   Glossary J-L
   Glossary M-O
   Glossary P-R
   Glossary S-U
   Glossary V-Z
Risk Assessment
Repair of Products
Corporate Profile
Standards and Regulations
   1910.211
   1910.212
   1910.213
   1910.216
   1910.217
   Appendix A
   Appendix B
   Appendix C
   Appendix D
   ISO and IEC Standards
   What Does OSHA Do?
   ANSI
   Domestic and International Standards Organizations
   OSHA Concept and Techniques of Machine Guarding

Home
Contact Our Sales Department
Contact Our Service Department